Asrock am2nf3-vsta manual

Page 4 3. In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by- step guide to the hardware installation. See the table below for connection details in accordance with the type of speaker you use.

Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Pre-installation Precautions Page Cpu Installation Step 4. The lever clicks on the side tab to indicate that it is locked. Page 15 DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. JR1 JL1 Jumper see p. Page Onboard Headers And Connectors see p.

As long as we have the latest driver, we will update it to our website in the future. Page 28 It will display Processor Maximum Voltage for reference. However, it is recom- mended to keep the default value for system stability. Page 29 [1T]. The default value is [Auto]. Burst Length Burst length can be set to 8, 4 or 2 beats. Bank Interleaving Interleaving allows memory accesses to be spread out over banks on the same node, or accross nodes, decreasing access contention.

It allows you to select the type of Primary VGA in case of multiple video controllers. The default value of this feature is [PCI]. Page Acpi Configuration Use this item to enable or disable Ring-In signals to turn on the system from the power-soft-off mode. Page Pcipnp Configuration Use this item to enable or disable the S. Self-Monitoring, Analysis, and Reporting Technology feature. Configuration options: [Disabled], [Auto], [Enabled].

To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

Hold components by the edges and do not touch the ICs. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component. When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard. Step 1. Unlock the socket by lifting the lever up to a 90 o angle. Step 2. Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle.

The CPU fits only in one correct orientation. Step 4. The lever clicks on the side tab to indicate that it is locked. After you install the CPU into this motherboard, it is necessary to install a larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation.

Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. For proper installation, please kindly refer to the instruction manuals of the CPU fan and the heatsink. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password.

User Manual Version 1. All rights reserved. Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock.

Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. Contents 1. Software Support Connector - 2 x Serial ATA 1. Pre-installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings. Step 3. Carefully insert the CPU into the socket until it fits in place.

You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual.

Buy as much as you need. Onboard Headers and Connectors Navigation Keys CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration Floppy Configuration Super IO Configuration USB Configuration Hardware Health Event Monitoring Screen