How to install corner bead around windows

Cover your window using methods adopted from drywall installation. Score along the seams where the trim and sill meet the wall using a utility knife to sever any caulk or paint.

Sand away any imperfections left on the wall from removing the trim and sill using sandpaper. Measure the dimensions of the window cavity. Cut a piece of self-sticking drywall tape to the length of the window frame.

Apply the tape to the first side of the window frame. Do the same for the other side. Press the tape's center into the corner of the edge of the drywall and the window frame. To prevent cracked drywall joints at the corners of windows and doors, place the sheet so the joint falls in the center of the opening, and then cut out the waste. Do not fasten the drywall to the header; use the interior casing to secure the loose edge of the drywall at that location.

Apply a thick coat of joint compound over both sides of the corner bead, using the 6-inch drywall knife. Apply another thick coat, using a inch drywall knife to cover a larger area.

Sand the dried compound with grit sandpaper until it is smooth. On occasion, I've used a 1. Usually, a wet light-duty sponge works well enough using the scrubby side. For severe cases, I've used Krud Kutter with the sponge. Careful moving any mud onto the glass; scratching may occur. Apply some dry wall adhesive to the masonry and then push a piece of plasterboard into the adhesive. Apply some more dry wall adhesive and then another piece of board.

Repeat this process until the plasterboard is almost level with where you wish the window lining to end. How do you install metal corner bead around a window?

Category: hobbies and interests beadwork. Spray adhesive on the walls on both sides of the corner if you're installing plastic beading. Set the beading in position and push it into the adhesive. How do you finish corner bead?

Do you have to tape drywall corners? Do you overlap corner bead? How do you nail corner beads? Note that filling the tapered seam first gives the knife a continuous bearing surface across the joint. For the second coat, choose a inch knife, and again bridge between the metal corner and the surface of the wall. Feather the compound along the wall to create a smooth transition. Use a inch knife for the third coat to feather the compound even further onto the wall. With bullnose bead, you might need to install the drywall sheets so that they terminate flush with the corner of the framing.

This placement is sometimes necessary to create clearance for the inside radius of the strip. Purchase bullnose bead strips before you hang the drywall to determine the proper corner treatment. Nail the metal or vinyl bullnose bead into place, spacing the fasteners about 8 inches apart along each leg.

If your outside corner is significantly larger or smaller than 90 degrees, ask a drywall supplier about the availability of off-angle bullnose beads. Make sure the materials you'll need to execute your design are available before you begin work. Composite materials can adapt to square or off-angle applications. Bullnose corners add style and interest to your installation, but they can also create problems when you install millwork.

For example, turning an outside corner with baseboards or crown moldings could call for fancy carpentry skills and tedious fabrication. Fortunately, there's a solution that you can simply nail in place when you're installing the bullnose bead.

Simply nail the blocks where you need them, and cut the strip of bullnose bead to fit. For a perfect size match, get both the bullnose bead and transition cap from a single manufacturer. Create a seamless corner by finishing your drywall with corner beads. Here are two easy techniques to get you started.

Each product we feature has been independently selected and reviewed by our editorial team. If you make a purchase using the links included, we may earn commission. Save Pin FB More. Corner of room with colorful artwork on walls. Tools Tin snips, for metal or vinyl beads Qty: 1 Scissors or a utility knife, for composite bead Qty: 1. Materials Corner bead Qty: 1 Ringshank drywall nails or corner clincher Qty: 1 Transition pieces to square off the corners at the top and bottom, optional Qty: 1.

Step A Bull is a popular choice to finish around window trim, but there is no need to stop there. Chamfer Bead , Bullnose , Niche Bead and assorted styles of Decorative L Bead can be mixed and matched to create a truly custom finish.

Perhaps what your project needs isn't to add wow factor, but just to get the job completed faster while also saving on material costs.

Introducing the L bead that can do exactly that, Oversized L Bead , also available in Super and Giant sizes with archway capabilities. Slip the Oversized L Bead over the window return and mud into place. The su rface of the Oversized L Bead is ready to be primed and painted. Finishing around windows with drywall and corner bead saves time and money since these products cost less than traditional wood and aluminum materials.

The customization possibilities are endless and high-end finishes can be created at an affordable price.